Samsung GALAXY Y (young) GT-S5360 Samsung logo only done via Odin
Status
Tools
Odin 1.85
File
1st Procedure Hard Reset but no lock
Press VOLUME UP + HOME + POWER and wait until the phone enter the Android System Recovery then select wipe date/factory reset & wipe cache partition
Procedure
1) Turn off your phone
2) Remove your SIM Card and SD Card
3) Extract previously downloaded firmware
4) Open ODIN 1.85 on your PC
5) Select from extracted archive: OPS-OPS, Bootloader, Phone-MODEM, PDA-CODE, CSC-CSC (leave EFS and One Package empty)
6) Connect your phone via USB into PC
7) When the screen is turned on hold POWER+VOLUME DOWN+HOME and wait until the phone enters the Download Mode
8) If ODIN detected and recognized your phone should light up the first square to the left side
9) Press “Start” button and wait, the process should take ~5 minutes
10) If all goes well your phone should reboot automatically
11) Square should change the color to blue and display “PASS” it means that flashing process was successful
Logs
Status
Tools
Odin 1.85
File
1st Procedure Hard Reset but no lock
Press VOLUME UP + HOME + POWER and wait until the phone enter the Android System Recovery then select wipe date/factory reset & wipe cache partition
Procedure
1) Turn off your phone
2) Remove your SIM Card and SD Card
3) Extract previously downloaded firmware
4) Open ODIN 1.85 on your PC
5) Select from extracted archive: OPS-OPS, Bootloader, Phone-MODEM, PDA-CODE, CSC-CSC (leave EFS and One Package empty)
6) Connect your phone via USB into PC
7) When the screen is turned on hold POWER+VOLUME DOWN+HOME and wait until the phone enters the Download Mode
8) If ODIN detected and recognized your phone should light up the first square to the left side
9) Press “Start” button and wait, the process should take ~5 minutes
10) If all goes well your phone should reboot automatically
11) Square should change the color to blue and display “PASS” it means that flashing process was successful
Logs
Code:
<ID:0/018> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> DefaultCalDataWithBoot_S5360XXKI6_REV05.tar.md5 is valid.
<OSM> PDA_S5360XXKI6_REV05.tar.md5 is valid.
<OSM> MODEM_S5360XXKI6_REV05.tar.md5 is valid.
<OSM> GT-S5360-MULTI-CSC-OXXKI6.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/018> Odin v.3 engine (ID:18)..
<ID:0/018> File analysis..
<ID:0/018> SetupConnection..
<ID:0/018> Initialzation..
<ID:0/018> Set PIT file..
<ID:0/018> DO NOT TURN OFF TARGET!!
<ID:0/018> Get PIT for mapping..
<ID:0/018> Firmware update start..
<ID:0/018> BcmBoot.img
<ID:0/018> NAND Write Start!!
<ID:0/018> HEDGE_NVRAM8_RF_LE.bin
<ID:0/018> sysparm_dep.img
<ID:0/018> Sbl.bin
<ID:0/018> boot.img
<ID:0/018> system.img
<ID:0/018> userdata.img
<ID:0/018> param.lfs
<ID:0/018> BcmCP.img
<ID:0/018> Transmission Complete..
<ID:0/018> Now Writing.. Please wait about 2 minutes
<ID:0/018> Receive Response form LOKE
<ID:0/018> csc.rfs
<ID:0/018> RQT_CLOSE !!
<ID:0/018> RES OK !!
<ID:0/018> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/018> Removed!!
No comments:
Post a Comment