Search This Blog Post

SAMSUNG S3(I9300)&GALAXY NOTE 2(N7100)Boot Reapir

  1. Dear Friends This Models(i9300&N7100) Boot Repair Step One i Already Posted Plz Check This Link
    IF YOU WANT MAKE A SAMSUNG S3(i9300)BOOT CARD(LOOK HERE)
    1)First Create Boot Card
    2)Download teraterm-4.78

    teraterm-4.78
    3)Connect Spt Box Also Take One Micro Uart Cable
    4)Open teraterm-4.78 (look the picture)


    Go To Device Manager Check Spt Port Number
    Open teraterm-4.78,Now New Window Apper.
    Select Spt Serial Port (look the picture)


    After Select The Serial Port Press Ok Button
    Next Go To Setup Click Serial Port Option
    Select Baud Rate 115200 Then Press Ok Button


    Insert Boot Card To Phone
    Connect Spt Via Uart Cable
    Then Insert Battery Next Hold Power Button Wait For Minutes

  2. Quote:
    1. pit_check_integrity: invalid pit.(0x0)
    2. pit_check_integrity: invalid pit.(0x0)
    3. update_guid_partition_table: There is no pit binary.
    4. fsd_reclaim 1283: MST is not recognized(mst.magic=0x0)
    5. fsd_reclaim 1284: MST is not recognized
    6. fsd_reclaim 1599: Error(nErr=0x0)
    7. fsd_reclaim 1604: j4fs_rw_start is set to default value(128KB)
    8. j4fs_open 153: Error(nErr=0x40000000)
    9. j4fs_read_file_bootloader 355: j4fs panic
    10. load_j4fs_param: 'param.j4fs' does not exist, make new one..
    11. j4fs_write_file_bootloader 184: j4fs panic
    12. fail
    13. j4fs_read_file_bootloader 355: j4fs panic
    14. load_j4fs_param: debug level file does not exist..*INCORRECT!*
    15. init_fuel_gauge: battery is not detected, do not init fuelgauge
    16. init_microusb_ic: MUIC: CONTROL1:0x1b
    17. init_microusb_ic: MUIC: CONTROL1:0x1b
    18. init_microusb_ic: MUIC: CONTROL2:0x3b
    19. init_microusb_ic: MUIC: CONTROL2:0x3a
    20. PMIC_ID = 0x2
    21. PMIC_IRQSRC = 0x0
    22. PMIC_STATUS1 = 0x10
    23. PMIC_STATUS2 = 0x0
    24. PMIC_PWRON = 0x2
    25. PMIC_IRQ1 = 0x27
    26. PMIC_IRQ2 = 0x0
    27. s5p_check_keypad: keypad value=0x0
    28. s5p_check_reboot_mode: INFORM3 = 0 ... skip
    29. s5p_check_upload: MAGIC CODE=d1b0f038
    30. microusb_get_attached_device: STATUS1:0x3c, 2:0x0
    31. s5p_check_download: update mode=0
    32. j4fs_read_file_bootloader 355: j4fs panic
    33. s5p_check_tzsw: invalid tzsw type! dummy?
    34. scr_draw_image: draw 'download_error.jpg'...
    35. j4fs_read_file_bootloader 355: j4fs panic
    36. read_param_file: 'download_error.jpg' j4fs read failed!
    37. fimd_div:13, div:1, FB_SOURCE_CLOCK:800000000, FB_PIXEL_CLOCK:57153600
    38. a2, 60, 90,
  1. After The Boot Repair Phone Must Trun On But Just For Light Nothing Show The Display.Dont Worry Put The Phone Download Mode Now Phone Enter Download Like This Picture
  2. open spt software use any version flash file.but remmber must use repartition option then flash it
  3. are you used odin software must use mx pit file&repartition option
  4. after the flash phone must powered but imei is damaged just rebuild imei via z3x.
  5. Quote:
    1. TN default
    2. <OK>
    3. <OK>
    4. [DVFS] INT(1) : 0
    5. DRAM Type : LPDDR2 8G
    6. [DVFS] MIF(3) : 0
    7. [EPLL][VPLL][CLK_DIV] OK
    8. <OK>
    9. [LOCK SW/HW]ARM:0/0 INT:0/0 G3D:0/0 MIF:0/0 SHIFT:0/0
    10. [DVFS] ARM(0) : 5
    11. [DVFS] INT(1) : 0
    12. [DVFS] G3D(2) : 0
    13. [DVFS] MIF(3) : 0
    14. [SD_INIT
    15. SDMMC_HighSpeedONE]
    16. SD_READ: 20000 20000 0x40008000 -> 668484 usec
    17. <OK>
    18. Inp32(uAddr) : 0xea00007e
    19. FW Booting
    20. [Patch Stop] This is not Rom Code.
  1. any one faced the error while boot repair
  2. this casue not software bad EMMC
  3. this phone cant repair with any jtag,must change the EMMC

All Mobile Solution Headline Animator

Please Log in