SAMSUNG S3(I9300)&GALAXY NOTE 2(N7100)Boot Reapir

1. Dear Friends This Models(i9300&N7100) Boot Repair Step One i Already Posted Plz Check This Link
   IF YOU WANT MAKE A SAMSUNG S3(i9300)BOOT CARD(LOOK HERE)
   1)First Create Boot Card
   2)Download teraterm-4.78
   teraterm-4.78
   3)Connect Spt Box Also Take One Micro Uart Cable
   4)Open teraterm-4.78 (look the picture)
   
   Go To Device Manager Check Spt Port Number
   Open teraterm-4.78,Now New Window Apper.
   Select Spt Serial Port (look the picture)
   
   After Select The Serial Port Press Ok Button
   Next Go To Setup Click Serial Port Option
   Select Baud Rate 115200 Then Press Ok Button
   
   
   Insert Boot Card To Phone
   Connect Spt Via Uart Cable
   Then Insert Battery Next Hold Power Button Wait For Minutes
   
2. Quote:

1. pit_check_integrity: invalid pit.(0x0) pit_check_integrity: invalid pit.(0x0) update_guid_partition_table: There is no pit binary. fsd_reclaim 1283: MST is not recognized(mst.magic=0x0) fsd_reclaim 1284: MST is not recognized fsd_reclaim 1599: Error(nErr=0x0) fsd_reclaim 1604: j4fs_rw_start is set to default value(128KB) j4fs_open 153: Error(nErr=0x40000000) j4fs_read_file_bootloader 355: j4fs panic load_j4fs_param: 'param.j4fs' does not exist, make new one.. j4fs_write_file_bootloader 184: j4fs panic fail j4fs_read_file_bootloader 355: j4fs panic load_j4fs_param: debug level file does not exist..*INCORRECT!* init_fuel_gauge: battery is not detected, do not init fuelgauge init_microusb_ic: MUIC: CONTROL1:0x1b init_microusb_ic: MUIC: CONTROL1:0x1b init_microusb_ic: MUIC: CONTROL2:0x3b init_microusb_ic: MUIC: CONTROL2:0x3a PMIC_ID = 0x2 PMIC_IRQSRC = 0x0 PMIC_STATUS1 = 0x10 PMIC_STATUS2 = 0x0 PMIC_PWRON = 0x2 PMIC_IRQ1 = 0x27 PMIC_IRQ2 = 0x0 s5p_check_keypad: keypad value=0x0 s5p_check_reboot_mode: INFORM3 = 0 ... skip s5p_check_upload: MAGIC CODE=d1b0f038 microusb_get_attached_device: STATUS1:0x3c, 2:0x0 s5p_check_download: update mode=0 j4fs_read_file_bootloader 355: j4fs panic s5p_check_tzsw: invalid tzsw type! dummy? scr_draw_image: draw 'download_error.jpg'... j4fs_read_file_bootloader 355: j4fs panic read_param_file: 'download_error.jpg' j4fs read failed! fimd_div:13, div:1, FB_SOURCE_CLOCK:800000000, FB_PIXEL_CLOCK:57153600 a2, 60, 90,

2. After The Boot Repair Phone Must Trun On But Just For Light Nothing Show The Display.Dont Worry Put The Phone Download Mode Now Phone Enter Download Like This Picture
3. 
4. 
5. open spt software use any version flash file.but remmber must use repartition option then flash it
6. are you used odin software must use mx pit file&repartition option
7. after the flash phone must powered but imei is damaged just rebuild imei via z3x.
8. Quote:

1. TN default <OK> <OK> [DVFS] INT(1) : 0 DRAM Type : LPDDR2 8G [DVFS] MIF(3) : 0 [EPLL][VPLL][CLK_DIV] OK <OK> [LOCK SW/HW]ARM:0/0 INT:0/0 G3D:0/0 MIF:0/0 SHIFT:0/0 [DVFS] ARM(0) : 5 [DVFS] INT(1) : 0 [DVFS] G3D(2) : 0 [DVFS] MIF(3) : 0 [SD_INIT SDMMC_HighSpeedONE] SD_READ: 20000 20000 0x40008000 -> 668484 usec <OK> Inp32(uAddr) : 0xea00007e FW Booting [Patch Stop] This is not Rom Code.

2. any one faced the error while boot repair
3. this casue not software bad EMMC
4. this phone cant repair with any jtag,must change the EMMC